notes:alpine - pup.casa Docs

Trace: • xfiles • alpine • maffs-ibook • labrador • pup2k • xencelabs-quickkeys • wiseau • asterisk
This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Alpine Linux ======

Notes and observations for setting up and maintaining systems.

===== 3.16 Desktop setup =====

With the release of 3.16.0 came a new tool, ''setup-desktop'', which prepares the system to be used graphically. I noticed some weirdness the first time I tried, so I'm documenting my efforts to reproduce here in an attempt to aid eventual bug reports.

==== [[machine:portapup|Sony Vaio VGN-P11Z/Q]] ====

This was the machine I first attempted this on, and where I noticed some issues. This machine is a 32-bit-only Intel Atom Z520 system, with an InsydeH2O "UEFI Ready BIOS", with 2GB of RAM. I used the ''alpine-3.16.0-extended-x86.iso'' image.

From boot, I ran ''setup-alpine'' as root, and did the following:

  * Set keymap to gb, gb-intl
  * Set the hostname
  * Set wlan0 as my interface
    * It was here that I noticed it didn't request my PSK, so once it set up wpa_supplicant, I exited and reconfigured wpa_supplicant.conf, replacing key_mgmt=NONE with psk=my psk. I then restarted setup, choosing 'none' instead of configuring an interface.
  * Declined to do any manual network configuration
  * Set the root password
  * Set the timezone to Europe/London
  * Declined to set a proxy
  * Set the APK mirror to the first in the list, ''dl-cdn.alpinelinux.org''
  * Set up a user with username 'maff', accepting the default full name of 'maff', with a password, no SSH key
  * Selected openssh as the SSH server
  * Selected sda as the disk to use, selecting 'sys' for usage, and confirming when prompted that I'd like to wipe the drive

After installation completed, I rebooted.

On first boot of the installed system, I logged in as root and immediately ran ''setup-desktop''. I selected ''xfce'' and rebooted once it was complete.

After rebooting and being presented with the lightdm login screen, I attempted to log in as the unprivileged user 'maff' I had created, however the X server simply exited and restarted, and I was again presented with the login screen.

I switched to tty1 and began tailing all available log files, then switched back to tty7 and attempted a login again. Switching back to tty1, I discovered two things:

  * Linux Kernel releases after 5.9 no longer support fbcon/vgacon scrolling via shift-page{up,down}, because apparently there's never in the modern world a case where you'd have access only to a framebuffer or VGA console and need to view many lines of text on screen within a very minimal system. I guess Linux from Scratch just got harder. I worked around this careless decision by piping my tail command into ''less'', which worked but scrolling one single line up or down took a full calendar second to happen
  * ''/lib/security/pam_elogind.so'' failed to be loaded, and so the login fails.
    * This later turned out not to be the problem, although I feel as though elogind being configured in lightdm but not installed is probably a bug in and of itself.

I installed elogind after verifying that package was the source for the missing file, and attempted to log in again, however I found logins were still failing. At this point, I noticed that the session was starting, and errors were to be logged to an .xsession-errors file, but ''find / -name .xsession-errors'' turned up bupkis. I assumed this file might simply have a discriminator at the end of the name after the X server exits, so I went to look in /home/maff to see, but found instead that /home was barren.

I created /home/maff and set ownership on it correctly, then attempted to log in graphically again, and this time I was able to.

==== QEMU VM with i686 processor, 2GB Memory, 8GB HDD, no UEFI, booting alpine-3.16.0-standard-x86.iso ====

Following the exact sequence of events as above, I replicated all issues I observed on the Vaio, with the exception of WiFi because I wasn't in the mood to emulate a wifi adaptor.

This time around, I created /home/maff before attempting to install elogind, and found that logins succeed without elogind being installed. I'm not sure what purpose elogind actually serves in this case, but an error is still logged about it, so either the setup-desktop script should install elogind, or lightdm should not be configured to load it.

==== QEMU VM with x64 processor, 2GB Memory, 8GB HDD, UEFI, booting alpine-3.16.0-standard-x86_64.iso ====

I followed the exact same steps again, however this time I noticed that after specifying that I wanted to use /dev/sda as a 'sys' volume, the error ''/sbin/setup-disk: line 1599: [ -z: not found'' was printed. Installation nonetheless completed without issue.

I observed that again I couldn't log in, and I again created the /home/maff directory without installing elogind, confirming that it worked.

==== QEMU VM with i686 processor, 2GB Memory, 8GB HDD, no UEFI, booting alpine-3.16.0-extended-x86.iso ====

This process was identical to using the 'standard' ISO, including all observed issues.

==== QEMU VM with x64 processor, 2GB Memory, 8GB HDD, UEFI, booting alpine-3.16.0-extended-x86_64.iso ====

This process was identical to using the 'standard' ISO, including all observed issues.

===== 3.16 Bug reports =====

''setup-user'' does not create user's home directory

''setup-desktop'' does not install elogind (possibly intentional, but..)

''setup-disk'' syntax error on line 1599 when booted via UEFI (looking at the code I don't actually see why it's a syntax error but the specific error is that it's trying to execute '[ -z' as a command, so maybe there's a weird unicode space or something)
Search

Navigation

Print/export

Tools
